Please check the box contents after unpacking. If any components are missing, please contact the dealer.
Name
Qty.
SP30 PIN Pad
1
Power Supply
1
Power Adaper
1
PRODUCT DESCRIPTION
The following section points out the various hardware features of the SP30.
Front View:
Back View:
BASIC OPERATING INSTRUCTIONS
The following section provides basic operating instructions for the SP30.
Power ON/OFF
Power ON: The terminal will automatically power on when connected for a power source.
Power OFF: Disconnect the terminal from its power source to power off.
SAM Installation
Remove SAM cover on back of terminal.
Insert SAM card into corresponding card slot.
Replace SAM cover.
CARD READERS
The SP30 includes the following card readers:
Magnetic Stripe Card
Slide the card through the card reader slot from top to bottom or from bottom to top with the magnetic strip oriented towards the body of the device. Make sure that the card is fully inserted into the card reader while swiping the card.
IC/Smart Card Reader
Insert the card fully into the reader with the metallic contacts facing up and towards the device. Make sure that the card is fully inserted into the card reader while scanning the card.
Contactless Card Reader
The contactless card reader reads cards and devices placed roughly within an inch (2.5 mm). For best results, place as close to the reader as possible and center the card over the terminal’s screen.
CLEANING THE DEVICE
Do not use industrial strength or abrasive cleaner.
Do not immerse the device in water or liquid.
Do not spray water or cleaner into EMV Card Reader or ports.
TERMINAL INSTALLATION AND USAGE TIPS
If any cables become damaged, seek a replacement.
Do not insert unknown materials into any port on the SP30; this may cause serious damage.
If repairs are required, please contact a professional technician instead of attempting them on your own.
Avoid exposing the device to an excessively hot, dusty, or strong electromagnetic environment.
Do not vibrate, shake, or drop the device.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Power ON: Press and hold the power button down for 3 to 5 seconds and then release.
Power OFF: Press and hold the power button down for 3 to 5 seconds and then release.
SAM/SD/SIM Card Installation
Remove the back cover.
Gently remove the battery from the device.
Insert the card into the relevant card slot.
Replace the battery and back cover.
CARD READERS
Magnetic Stripe Card
IC/Smart Card Reader
Contactless Card Reader
CLEANING THE DEVICE
Do not use industrial strength or abrasive cleaner as it may damage or scratch the screen.
Do not immerse the device in water or liquid.
Do not spray water or cleaner into EMV Card Reader or ports.
To clean the screen, apply distilled water or mild glass cleaner onto a soft, lint-free cloth and gently wipe terminal.
LITHIUM ION BATTERY
Do not use or place the battery in direct sunlight and/or smokey, dusty environments.
Do not strike, squeeze, and/or tread on battery.
Do not throw the battery in any liquids or place in/near fires.
If the battery is deformed or damaged, please stop using immediately and replace it.
If the continuous working time is only half of a new battery, the battery life may be at its end. Please replace it.
The specified battery model and charger must be used, otherwise there may be an explosion.
The charging time cannot exceed 24 hours. If the battery is out of power, please recharge in an appropriate time and then disconnect the device.
Please recharge the battery at least once every 6 months to avoid shortening its life.
Replace battery every two years.
Be sure to follow the instructions to dispose of wasted batteries.
TERMINAL INSTALLATION AND USAGE TIPS
If any cables become damaged, seek a replacement.
Do not insert unknown materials into any port on the S920; this may cause serious damage.
If repairs are required, please contact a professional technician instead of attempting them on your own.
Avoid exposing the device to an excessively hot, dusty, or strong electromagnetic environment.
Do not vibrate, shake, or drop the device.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For non-5GWiFi version
FCC compliance statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help.
FCC SAR statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body ISED compliance statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
IC SAR statement This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement non contrôlé. L’utilisateur final doit suivre les instructions spécifiques pour satisfaire les normes. Cet émetteur ne doit pas être co-implanté ou fonctionner en conjonction avec toute autre antenne ou transmetteur. Le dispositif portatif est conçu pour répondre aux exigences d’exposition aux ondes radio établie par le développement énergétique DURABLE. Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la plus élevée signalée en vertu de cette norme lors de la certification de produit à utiliser lorsqu’il est correctement porté sur le corps.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by PAX Technology, Inc. is under license. Other trademarks and trade names are those of their respective owners.
PAX Technology Inc reserves the right to change product technology specifications without notification.
Please check the box contents after unpacking. If any components are missing, please contact the dealer.
Name
Qty.
S300 PIN Pad
1
Power Supply
1
Power Adaper
1
Stylus Pen
1
PRODUCT DESCRIPTION
The following section points out the various hardware features of the S300.
Front View:
Back View:
BASIC OPERATING INSTRUCTIONS
The following section provides basic operating instructions for the S300.
Power ON/OFF’
Power ON: The terminal will automatically power on when connected for a power source.
Power OFF: Disconnect the terminal from its power source to power off.
SAM Installation
Remove SAM cover on back of terminal.
Insert SAM card into corresponding card slot.
Replace SAM cover.
CARD READERS
The S300 includes the following card readers:
Magnetic Stripe Card
Slide the card through the card reader slot from top to bottom or from bottom to top with the magnetic strip oriented towards the body of the device. Make sure that the card is fully inserted into the card reader while swiping the card.
IC/Smart Card Reader
Insert the card fully into the reader with the metallic contacts facing up and towards the device. Make sure that the card is fully inserted into the card reader while scanning the card.
Contactless Card Reader
The contactless card reader reads cards and devices placed roughly within an inch (2.5 mm). For best results, place as close to the reader as possible and center the card over the terminal’s screen.
CLEANING THE DEVICE
Do not use industrial strength or abrasive cleaner.
Do not immerse the device in water or liquid.
Do not spray water or cleaner into EMV Card Reader or ports.
TERMINAL INSTALLATION AND USAGE TIPS
If any cables become damaged, seek a replacement.
Do not insert unknown materials into any port on the S300; this may cause serious damage.
If repairs are required, please contact a professional technician instead of attempting them on your own.
Avoid exposing the device to an excessively hot, dusty, or strong electromagnetic environment.
Do not vibrate, shake, or drop the device.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
