CONTENTS CHECKLIST
| Name | Qty. |
| Q30 POS Terminal | 1 |
| Communication Cable | 1 |
| AC Power Adapter | 1 |
| Privacy Shield | 1 |
| Decorative Plug | 1 |
PRODUCT DESCRIPTION
The following section points out the various hardware features of the Q30.
Front View:
Back View:
BASIC OPERATING INSTRUCTIONS
The following section provides basic operating instructions for the Q30.
Power Connection
- Power can be supplied to the Q30 by connecting the AC power adapter to the data cable, as in the case of RS232 or USB configurations, or via a powered USB cable (12V Powered USB) where the connected POS terminal provides the power.
Please Note: To connect the communication cable to the device, remove the back cover and connect the communication cable head to the 2ร7 pin interface.
Reset Device
- To reset the terminal, press and hold the reset button for 4-6 seconds using a pen or similar item.
USB and PIN Pad Connection
The Q30โs 2ร7 pin communication supports PIN Pad connection as well as USB data connection for downloading and debugging purposes.
SAM/SIM Installation
WARNING: Power down the terminal before installing SIM cards or Micro SD cards. If the terminal is still powered on during an attempted SIM or SD card installation or removal, both the terminal and the card can be damaged irreparably.
- Power down the Q30.
- Unscrew and open back cover.
Gently press and slide SIM or Micro SD
door toward outer edge of terminal and
open hinged door. - Seat card with gold
connectors down into slot, aligning with
opening. - Gently press and slide door closed.
Stand Installation
- Insert the metal standโs prongs into the three stand slots on the underside of terminal.
- Slide terminal firmly into place on stand.
CARD READERS
The Q30 includes the following card readers:
Magnetic Stripe Card
Slide the card through the card reader slot from top to bottom or from bottom to top with the magnetic strip oriented towards the body of the device. Make sure that the card is fully inserted into the card reader while swiping the card.
IC/Smart Card Reader
Insert the card fully into the reader with the metallic contacts facing up and towards the device. Make sure that the card is fully inserted into the card reader while scanning the card.
Contactless Card Reader
The contactless card reader reads cards and devices placed roughly within an inch (2.5 mm). For best results, place as close to the reader as possible and center the card over the contactless area at the top of the terminal.
CLEANING THE DEVICE
- Do not use industrial strength or abrasive cleaner as it may damage or scratch the screen.
- Do not use industrial strength or abrasive cleaner.
- Do not immerse the device in water or liquid.
- Do not spray water or cleaner into EMV Card Reader or ports.
TERMINAL INSTALLATION AND USAGE TIPS
- If any cables become damaged, seek a replacement.
- Do not insert unknown materials into any port on the Q30; this may cause serious damage.
- If repairs are required, please contact a professional technician instead of attempting them on your own.
- Avoid exposing the device to an excessively hot, dusty, or strong electromagnetic environment.
- Do not vibrate, shake, or drop the device.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the userโs authority to operate the equipment.
For non-5GWiFi version
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the userโs authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
โ Reorient or relocate the receiving antenna.
โ Increase the separation between the equipment and receiver.
โ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
โ Consult the dealer or an experienced radio/TV technician for help.
FCC SAR statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body
ISED compliance statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadaโs licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Lโรฉmetteur/rรฉcepteur exempt de licence contenu dans le prรฉsent appareil est conforme aux CNR dโInnovation, Sciences et Dรฉveloppement รฉconomique Canada applicables aux appareils radio exempts de licence. Lโexploitation est autorisรฉe aux deux conditions suivantes :
(1) Lโappareil ne doit pas produire de brouillage;
(2) Lโappareil doit accepter tout brouillage radioรฉlectrique subi, mรชme si le brouillage est susceptible dโen compromettre le fonctionnement.
IC SAR statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.
Cet รฉquipement est conforme aux limites dโexposition aux rayonnements ISED รฉtablies pour un environnement non contrรดlรฉ. Lโutilisateur final doit suivre les instructions spรฉcifiques pour satisfaire les normes. Cet รฉmetteur ne doit pas รชtre co-implantรฉ ou fonctionner en conjonction avec toute autre antenne ou transmetteur.
Le dispositif portatif est conรงu pour rรฉpondre aux exigences dโexposition aux ondes radio รฉtablie par le dรฉveloppement รฉnergรฉtique DURABLE. Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la plus รฉlevรฉe signalรฉe en vertu de cette norme lors de la certification de produit ร utiliser lorsquโil est correctement portรฉ sur le corps.
The Bluetoothยฎ word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by PAX Technology, Inc. is under license. Other trademarks and trade names are those of their respective owners.
PAX Technology Inc reserves the right to change product technology specifications without notification.